Ads Security FA700KP-ADS Guia de preparacion descargar pdf (Pagina 15)

– 15 –

5800 Series Transmitter Input Loop Identification

All of the transmitters illustrated below have one or more unique factory assigned input (loop) ID codes.

Each of the

inputs requires its own programming zone

(e.g., a 5804's four inputs require four programming zones).

WIRELESS INPUT TYPES

"RF" (Supervised RF) Type send periodic check-in

signals, as well as fault, restore and low battery signals.

The transmitter must remain within the receiver's range.

“UR" (Unsupervised RF) Type send all the signals that

the "RF" Type does, but the control does not supervise

the check-in signals. The transmitter may, therefore, be

carried off-premises.

"BR" (Unsupervised Button RF) Type only send fault

signals. They do not send restore or check-in signals.

They will indicate a low battery condition when tested or

activated normally. They can be carried off-premises.

Note: For information on any transmitter not shown

above, refer to the instructions accompanying that

transmitter for details regarding loop numbers, etc.

UL NOTE: The following transmitters are not intended for

use in UL installations: 5802MN, 5802MN2, 5804, 5804BD,

5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850.

The 5827BD and 5800TM can be used in UL Listed

Residential Burglar installations.

5802MN

ENROLL AS

"UR" OR "RF"

LOOP

V20P-006-V0

5817

ENROLL AS

"RF"

5890

ENROLL AS

"RF" OR "RM"

LOOP 1

5808

ENROLL AS

"RF"

LOOP 1

5809

ENROLL AS

"RF"

5850 (GBD)

ENROLL AS

"RF"

(Green)

(Red)

(Yellow)

5804BD

ENROLL AS

"BR"

LOOP 4

YOU MUST

ENROLL

THIS BUTTON

SET

HOUSE

CODE

LOOP 3

LOOP 1

LOOP 2

5804

ENROLL AS "BR"

5816MN

ENROLL AS

"RF"

LOOP 2

(REED)

5816

ENROLL AS

"RF"

LOOP 1

(TERMINALS)

LOOP 2

(REED)

LOOP 3

(TERMINALS)

5819S (WHS & BRS)

ENROLL AS

"RF"

LOOP 1

(INTERNAL

SHOCK

SENSOR

LOOP 2

(REED)

5819

ENROLL AS

"RF"

LOOP 2

(REED)

LOOP 3

(TERMINALS)

LOOP 1

(TERMINALS)

5801

ENROLL AS

"UR" OR "RF"

LOOP 3

LOOP 1

LOOP 2

LOOP 4

YOU MUST

ENROLL

THIS

BUTTON

LOOP 1

LOOP 2

LOOP 4

YOU MUST

ENROLL

THIS

BUTTON

LOOP 3

LOOP

MOTION

LOOP 2

(AUX.

CENTER)

LOOP 1

(PRIMARY)

LOOP 3

(AUX.

RIGHT)

LOOP 1

(TERMINALS)

ALTERNATE

POSITION

FOR LOOP 2

Wireless Key Predefined Default Templates

For 5804

Loop Function Zone Type

For 5804BD

Loop Function Zone Type

TEMPLATE 1 1 No Response 23 TEMPLATE 4 1 No Response 23

2 Disarm 22 2 No Response 23

3 Arm Away 21 3 Arm Away 21

4 No Response 23 4 Disarm 22

TEMPLATE 2 1 No Response 23 TEMPLATE 5 1 No Response 23

2 Disarm 22 2 Arm Stay 20

3 Arm Away 21 3 Arm Away 21

4 Arm Stay 20 4 Disarm 22

TEMPLATE 3 1 24-hour audible 7 TEMPLATE 6 1 24-hour audible 7

2 Disarm 22 2 Arm Stay 20

3 Arm Away 21 3 Arm Away 21

4 Arm Stay 20 4 Disarm 22

Table of Device Addresses

This Device Uses Address

Reports as

†† Enabled By…

RF Receiver 00 100 *56 zone programming: input device type entry

AUI 1 01 101 automatic if AUI enable field *189 enabled for AUI 1

AUI 2 02 102 automatic if AUI enable field *189 enabled for AUI 2

Long Range Radio 03 103 automatic if output to long range radio field *29 enabled

FA4286 Voice Module 04 104 automatic if phone module access code field *28 enabled

Zone Expanders (4219/4229):

module 1 (for zones 09 - 16)

module 2 (for zones 17 - 24)

module 3 (for zones 25 - 32)

module 4 zones 33 - 40

module 5 zones 41 - 48

09**

10**

11**

107

108

109

110

111

*56 zone programming: input device type entry, then:

automatic if zone no. 9-16 entered as AW type or relay assigned

automatic if zone no. 17-24 entered as AW type or relay assigned

automatic if zone no. 25-32 entered as AW type or relay assigned

automatic if zone no. 33-40 entered as AW type or relay assigned

automatic if zone no. 41-48 entered as AW type or relay assigned

Relay Modules (4204):

module 1

module 2

module 3

module 4

14**

15**

112

113

114

115

*79 output device programming: device address prompt:

entered at device address prompt

Keypads:

keypad 1

keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

n/a

data field programming as listed below:

always enabled, all sounds enabled.

data field *190

data field *191

data field *192

data field *193

data field *194

data field *195

data field *196

5800TM Module 28 n/a automatic

** These module addresses apply to FA168CPS only.

†† Addressable devices are identified by “1” plus the device address when reporting. Enter report code for zone 91 to enable addressable device reporting (default =

reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification keypad display options.

1 2 ... 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Ads Security FA700KP-ADS Guia de preparacion Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Ads Security FA700KP-ADS